We have found this article pertaining to How to Install a Bathtub Yourself down the page on the web and accepted it made good sense to talk about it with you on my blog.
Mounting a bath tub isn't precisely brain surgery, however it does call for solid plumbing, woodworking, and occasionally, tiling skills. Changing an old bathtub with a new one is also a reasonably hard project. If the old bathtub is readily easily accessible, the job can move rapidly; if you have to open up a wall to eliminate the old tub and position the brand-new tub, the task is a lot harder. In either instance, the task is within a home handyman's skills, although you will certainly need a helper to leave the old tub as well as embeded in the brand-new one. Make sure you have actually certified on your own for the task as well as are comfortable trying it. Instead of employing a specialist to take over a halfway-completed job, it is much better to take into consideration utilizing one before you begin. Possibilities are you might need an expert plumber to make tube connections.
This article will help you install a brand-new bath tub in your bathroom if you have already acquired a brand-new tub as well as don't need to transform the arrangement of your previous water system pipes.
Your devices and also material checklist ought to consist of the following:
Removing Old Touches
If you require to replace old faucets with brand-new ones as a part of your installation, after that the first thing you ought to do is detach the supply of water. After doing so, activate the taps to drain any type of water continuing to be in the system. The procedure of removing the existing taps can be rather problematic as a result of the limited access that is frequently the situation.
Make use of a container wrench (crowsfoot spanner) or a tap device to undo the nut that attaches the supply pipelines to the faucets. Have a towel prepared for the staying water that will come from the pipes. As soon as the supply pipes have actually been removed, utilize the exact same device to loosen up the nut that holds the taps onto the bath/basin. You will need to stop the solitary taps from transforming throughout this procedure. Once the faucets have actually been gotten rid of, the holes in the bath/basin will certainly need to be cleansed of any old sealing compound.
Before proceeding to fit the brand-new faucets, contrast the pipe connections on the old faucets to the new faucets. If the old taps are longer than the new taps, after that a shank adapter is needed for the brand-new taps to fit.
Suitable New Taps
If the tails of the new faucets are plastic, then you will require a plastic connector to prevent damages to the thread. One end of the connector fits on the plastic tail of the faucet and the various other end offers a link to the existing supply pipes.
If you need to fit a monobloc, after that you will require minimizing couplers, which connects the 10mm pipeline of the monobloc to the common 15mm supply pipeline.
Next, place the tap in the placing hole in the bath/basin ensuring that the washers are in area between the tap and also the sink. Safeguard the faucet in place with the producer supplied backnut. When the faucet is securely in position, the supply pipelines can be attached to the tails of the taps. The taps can either be connected by using corrugated copper piping or with regular tap ports. The previous kind should be connected to the faucet ends initially, tightening only by hand. The supply pipes can later on be attached to the various other end. Tighten both ends with a spanner after both ends have actually been linked.
Setting up the Bath tub
Using the two wood boards under its feet, place the bathtub in the needed position. The wood boards are useful in uniformly spreading out the weight of the bath tub over the area of the boards as opposed to focusing all the weight onto 4 tiny points.
The following goal is to make certain that the bath tub is leveled all round. This can be accomplished by checking the level as well as changing the feet on the bath tub till the spirit level checks out level.
To install faucets, fit the bottom of the furthest adaptable faucet connector to the suitable supply pipeline by making a compression sign up with; then do the very same for the other faucet.
Activate the water supply and also examine all joints as well as new pipework for leaks and also tighten them if essential. Fill the bath tub and also examine the overflow electrical outlet as well as the typical electrical outlet for leakages.
Finally, take care of the bathroom paneling as defined in the manufacturer's instruction manual. Tiling and sealing around the bath tub needs to wait up until the bath tub has actually been utilized at the very least when as this will certainly resolve it into its final setting.
Preparing for the Installation
First of all, the supporting frame provided with the bathroom needs to be fitted (if called for) according to the producer's guidelines. Next, fit the taps or mixer to the tub. When fitting the tap block, it is very important to make certain that if the faucet includes a plastic washing machine, it is fitted in between the bath and also the taps. On a plastic bathroom, it is likewise practical to fit a supporting plate under the taps unit to stop stress on the tub.
Fit the versatile tap ports to the bottom of the two faucets making use of 2 nuts as well as olives (sometimes supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the electrical outlet via the hole in the bathroom. Utilize the nut supplied by the supplier to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the versatile overflow pipeline to the overflow outlet. After that, screw the pipeline to the overflow face which need to be fitted inside the bathroom. Make sure you utilize every one of the supplied washing machines.
Link the catch to the bottom of the waste outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Connect the bottom of the overflow tube in a comparable manner.The bathroom need to now be ready to be suited its last placement.
Tiling Around the Bathtub
In the location where the bath fulfills the ceramic tile, it is required to seal the accompanies a silicone rubber caulking. This is necessary as the installation can move sufficient to crack a stiff seal, causing the water to pass through the wall between the bathroom as well as the tiling, leading to issues with wetness and also feasible leaks to the ceiling below.
You can select from a range of coloured sealers to blend in your fixtures and also installations. They are offered in tubes as well as cartridges, and can securing spaces up to a width of 3mm (1/8 inch). If you have a larger space to fill, you can load it with spins of soaked newspaper or soft rope. Bear in mind to constantly fill up the tub with water prior to securing, to permit the motion experienced when the tub remains in use. The sealer can crack fairly very early if you do not take into consideration this activity prior to sealing.
Alternatively, ceramic coving or quadrant floor tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are additionally quickly offered on the marketplace. It is suggested to fit the ceramic tiles making use of water-resistant or waterproof glue and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I recently found that piece about How to Install a Bathtub Yourself when doing a search on the search engines. Kindly take the time to share this write-up if you appreciated it. Kudos for your time. Visit again soon.
No more leaks, call us!